Buy Enamel ML-158
Enamel ML-158

Enamel ML-158

Products from producer
In stock
Reconfirm the price with seller
Payment:
Shipping:
Seller
Belarus, Lida
(View map)
+375 
Display phones

Company rating

100% of positive reviews from 5
10
10 years on Allbiz
Technical characteristics
  • BrandЛакокраска, ОАО
  • Country of manufactureBelarus
  • Basis of the enamelAlkyd
  • Number of componentsTwo-component
  • PurposeUniversal
  • Degree of brillianceFrosted
  • ColorIn assortment
Description

Type: Enamel is a suspension of pigments and fillers in a solution of an alkyd and melamine - formaldehyde resins.

Scope: Enamel intended for protective and decorative metal coloring.

Specifications

" The name of indicators requirements ROV
one Color enamel coating Must be within the tolerances established by the approval of the color samples correspond to a scale or color RAL register.
2 Appearance of the enamel coating After drying the enamel must form a homogeneous semi - matt surface with a characteristic appearance resembling shagreen skin.
3 Viscosity according viscometer VZ - 246 (nozzle 4 mm) at a temperature (20,0 ± 0,5) ° C, not less than 80
4 Mass fraction of solids, %

black

other colors

54 - 60

61 - 69

5 The degree of grinding of enamel, um, not more than fifty
6 The drying time of up to 3 degrees at a temperature of (130 ± 2) ° C, min, max 60
7 Elasticity coating flexural mm, not more than one
8 Impact resistance coating on the device U - 1, cm, at least fifty
nine coating gloss by photoelectric gloss meter SE - 2,% 8 - 15
10 Coating hardness pendulum device TML (pendulum A) rel. units. , at least 0.26
eleven Spreading dried coating, g / m 2 , no more than one hundred
12 Resistance to static action at (20 ± 2) ° C, h, min

distilled water

gasoline

industrial oil





24

4

24

thirteen Life of the coating under operating conditions:

NF1, years, not less

T1 years, at least


 


 

2

one

To eliminate condensation substrate temperature should be above the dew point temperature of not less than 3 ° C.

Advantages: Enamel provides a coating with a distinctive appearance resembling shagreen skin. Enamel coatings have high decorative properties when operating at atmospheric conditions and indoors. Coating enamels resistant to temperature changes in the range from minus 60 ° C to plus 60 ° C.


Recommendations on Application: Before applying the enamel primed surface sanded if necessary, dedusted, degreased and thoroughly dried. Previously painted surfaces purified by the fragile layers of the old coating, delaminated old coating removed, the entire surface is cleaned mechanically, dedusted, degreased and dried. To eliminate condensation substrate temperature should be above the dew point temperature of not less than 3 ° C. Recommended primers: PL - 03 R (for dyeing brass and steel) or primer GP - 0119, GP - 0119 "L", or PL - 03 F (for coloring of aluminum and its alloys). Previously painted surfaces must be cleaned of dust, grease, grind, degrease, dry and produce a test staining. In the case of blistering or peeling of the old coating should be removed.

 

Before applying the enamel thoroughly mixed, diluted with toluene in an amount of not more than 25% by weight of the undiluted enamel and then filtered through a mesh. The enamel is applied at a temperature below 5 ° C and a relative humidity of 80% . The enamel is applied by pneumatic spraying. The recommended coating system:

- first layer - priming PL - 03 K or GF - 0119, GP - 0119 "L", or PL - 03 J. Drying in accordance with the ROV active material.

- second layer - applying enamel ML - 158 by air pressure


0.3 - 0.4 MPa and extract at least 10 minutes at a temperature (20 ± 2) ° C.

 

- third layer - applying enamel ML - 158 by air pressure


0.05 MPa and drying for 60 minutes at a temperature of (130 ± 2) ° C.

 

The thickness of the dried coating complex - 55 - 80 microns. After staining should avoid strong mechanical stress for 7 days.

Flow enamel layer coating is 75 - 120 g / m², depending on the complexity of the surface to be painted, the color of enamel, staff, and other factors.

Coating Lifetime: The coating system consisting of two layers of enamel, applied to the primed surface (primer FL - 03 K according to GOST 9109 thickness of 10 - 15 microns) retains protective and decorative properties in conditions of moderately cold climate for at least 2 years and in a tropical climate within 1 year. The thickness of the dried complex coating is 55 - 80 microns.

Comments about the company  Lakokraska, OAO
100%
of positive feedback from the 5
100% of responses during the day
100% of transactions executed in time
100% of actual goods description
This means that 100% of buyers found cooperation with this company successful and recommend this seller
all (5) positive (5) negative (0)
Good
раимбеков жанат чалбаевич
раимбеков жанат чалбаевич
22.05.2019
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
пока идут переговоры Надеемся на успех
Prompt response: Within one hour
Was the order is executed in time: Yes
Corresponding of goods/services description: Yes
Good
Игорь
Игорь
08.03.2019
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
Отлично. Оперативно. Тактично.
Prompt response: Within one hour
Was the order is executed in time: Yes
Corresponding of goods/services description: Yes
Good
Anonymous
26.03.2018
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
Prompt response: Within one hour
Was the order is executed in time: I can not appreciate
Corresponding of goods/services description: I can not appreciate
Good
Дмитрий
Дмитрий
22.09.2017
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
супер пупер молодцы !
Prompt response: Within one hour
Was the order is executed in time: Yes
Corresponding of goods/services description: Yes
Contact the seller
Enamel ML-158
Enamel ML-158
We recommend to see
Shipping method
Payment method
Compare0
ClearSelected items: 0